Year |
Citation |
Score |
2020 |
Gattmah J, Ozturk F, Orhan S. A new development of measurement technique for residual stresses generated by the cold tube drawing process with a fixed mandrel The International Journal of Advanced Manufacturing Technology. 108: 3675-3687. DOI: 10.1007/S00170-020-05645-8 |
0.35 |
|
2019 |
Kilic S, Kacar I, Sahin M, Ozturk F, Erdem O. Effects of Aging Temperature, Time, and Pre-Strain on Mechanical Properties of AA7075 Materials Research-Ibero-American Journal of Materials. 22. DOI: 10.1590/1980-5373-Mr-2019-0006 |
0.388 |
|
2019 |
Gattmah J, Ozturk F, Orhan S. Numerical Simulation of Bending Process for Steel Plate Using Finite Element Analysis Arabian Journal For Science and Engineering. 44: 10285-10292. DOI: 10.1007/S13369-019-04119-8 |
0.449 |
|
2018 |
Hou Z, Sheikh-Ahmad J, Jarrar F, Ozturk F. Residual Stresses in Dissimilar Friction Stir Welding of AA2024 and AZ31: Experimental and Numerical Study Journal of Manufacturing Science and Engineering-Transactions of the Asme. 140: 51015. DOI: 10.1115/1.4039074 |
0.312 |
|
2018 |
Dong J, Ozturk F, Jarrar F, Sheikh-Ahmad JY. Numerical Post-Buckling Analysis of Mechanically Lined Corrosion Resistant Alloy Pipes Journal of Pressure Vessel Technology-Transactions of the Asme. 140: 14502. DOI: 10.1115/1.4038225 |
0.309 |
|
2018 |
Kilic S, Ozturk F, Picu CR. Investigation of the Performance of Flow Models for TWIP Steel Journal of Materials Engineering and Performance. 27: 4364-4371. DOI: 10.1007/S11665-018-3504-6 |
0.39 |
|
2017 |
Kilic S, Ozturk F. Evaluation of formability under different deformation modes for TWIP900 steel Journal of Engineering Materials and Technology-Transactions of the Asme. 139: 31001. DOI: 10.1115/1.4035621 |
0.313 |
|
2017 |
Guo T, Ozturk F, Jarrar F, Sheikh-Ahmad JY. Analysis of Contact Pressure of Mechanically Lined Corrosion Resistant Alloy Pipe by Hydraulic Expansion Process Journal of Pressure Vessel Technology-Transactions of the Asme. 139: 21212. DOI: 10.1115/1.4035314 |
0.303 |
|
2017 |
Li K, Jarrar F, Sheikh-Ahmad J, Ozturk F. Using coupled Eulerian Lagrangian formulation for accurate modeling of the friction stir welding process Procedia Engineering. 207: 574-579. DOI: 10.1016/J.Proeng.2017.10.1023 |
0.397 |
|
2017 |
Gattmah J, Ozturk F, Orhan S. Effects of Process Parameters on Hot Extrusion of Hollow Tube Arabian Journal For Science and Engineering. 42: 2021-2030. DOI: 10.1007/S13369-017-2434-1 |
0.352 |
|
2017 |
Gattmah J, Ozturk F, Orhan S. Experimental and finite element analysis of residual stresses in cold tube drawing process with a fixed mandrel for AISI 1010 steel tube The International Journal of Advanced Manufacturing Technology. 93: 1229-1241. DOI: 10.1007/S00170-017-0583-8 |
0.325 |
|
2017 |
Li Z, Dai G, Shi J, Jarrar F, Ozturk F, Sheikh-Ahmad J. Using the particle swarm optimization method for the constitutive modeling of AZ31B Materialwissenschaft Und Werkstofftechnik. 48: 993-997. DOI: 10.1002/Mawe.201700043 |
0.397 |
|
2016 |
Juneidi N, Asha R, Jarrar F, Ozturk F. Design for Manufacturing of an Aluminum Superplastic AA5083 Alloy Plate-Fin Heat Exchanger Journal of Materials Science Research. 5: 121. DOI: 10.5539/Jmsr.V5N2P121 |
0.341 |
|
2016 |
Ozturk F, Ece RE, Polat N, Koksal A, Evis Z, Sheikh-Ahmad JY. Application of Electric Resistance Heating Method on Titanium Hot Forming at Industrial Scale Arabian Journal For Science and Engineering. 41: 4441-4448. DOI: 10.1007/S13369-016-2159-6 |
0.335 |
|
2016 |
Sheikh-Ahmad JY, Ozturk F, Jarrar F, Evis Z. Thermal history and microstructure during friction stir welding of Al–Mg alloy International Journal of Advanced Manufacturing Technology. 1-11. DOI: 10.1007/S00170-015-8239-Z |
0.342 |
|
2015 |
Ozturk F. Prediction of forming limit diagram using Marciniak–Kuczynski and Swift-Hill models via yield criteria for TRIP800 Advances in Materials and Processing Technologies. 1: 619-625. DOI: 10.1080/2374068X.2016.1147760 |
0.331 |
|
2015 |
Kilic S, Ozturk F, Sigirtmac T, Tekin G. Effects of Pre-strain and Temperature on Bake Hardening of TWIP900CR Steel Journal of Iron and Steel Research International. 22: 361-365. DOI: 10.1016/S1006-706X(15)30012-1 |
0.446 |
|
2014 |
Ozturk F, Toros S, Kilic S, Kacar I. Evaluation of anisotropy by two different tests for TRIP800 steel Key Engineering Materials. 622: 1139-1144. DOI: 10.4028/Www.Scientific.Net/Kem.622-623.1139 |
0.389 |
|
2014 |
Ozturk F, Kacar I, Jarrar F. Defects and Remedies in Stamping of Advanced High Strength Steels Modern Mechanical Engineering. 1: 68-74. DOI: 10.15377/2409-9848.2014.01.02.4 |
0.363 |
|
2014 |
Ozturk F, Toros S, Kilic S. Effects of anisotropic yield functions on prediction of forming limit diagrams of DP600 advanced high strength steel Procedia Engineering. 81: 760-765. DOI: 10.1016/J.Proeng.2014.10.073 |
0.39 |
|
2013 |
Dilmec M, Selcuk Halkaci H, Ozturk F, Turkoz M. Detailed investigation of forming limit determination standards for aluminum alloys Journal of Testing and Evaluation. 41. DOI: 10.1520/Jte104356 |
0.434 |
|
2013 |
Ozturk F, Polat A, Toros S, Picu RC. Strain Hardening and Strain Rate Sensitivity Behaviors of Advanced High Strength Steels Journal of Iron and Steel Research International. 20: 68-74. DOI: 10.1016/S1006-706X(13)60114-4 |
0.471 |
|
2013 |
Ozturk F, Ece RE, Polat N, Koksal A, Evis Z, Polat A. Mechanical and microstructural evaluations of hot formed titanium sheets by electrical resistance heating process Materials Science and Engineering A. 578: 207-214. DOI: 10.1016/J.Msea.2013.04.079 |
0.363 |
|
2013 |
Dilmec M, Halkaci HS, Ozturk F, Livatyali H, Yigit O. Effects of sheet thickness and anisotropy on forming limit curves of AA2024-T4 International Journal of Advanced Manufacturing Technology. 67: 2689-2700. DOI: 10.1007/S00170-012-4684-0 |
0.458 |
|
2012 |
Toros S, Polat A, Ozturk F. Formability and springback characterization of TRIP800 advanced high strength steel Materials and Design. 41: 298-305. DOI: 10.1016/J.Matdes.2012.05.006 |
0.401 |
|
2011 |
Toros S, Ozturk F, Kaya M. Modeling Uniaxial, Temperature, and Strain Rate Dependent Behavior of AZ31 Alloy by Softening Model Key Engineering Materials. 473: 624-630. DOI: 10.4028/Www.Scientific.Net/Kem.473.624 |
0.447 |
|
2011 |
Ozturk F, Ece RE, Polat N, Koksal A. Assessment of electrical resistance heating for hot formability of Ti-6Al-4V alloy sheet Key Engineering Materials. 473: 130-136. DOI: 10.4028/Www.Scientific.Net/Kem.473.130 |
0.364 |
|
2011 |
Toros S, Kilic S, Ozturk F. The Effects of Material Thickness and Deformation Speed on Springback Behavior of DP600 Steel Advanced Materials Research. 636-645. DOI: 10.4028/Www.Scientific.Net/Amr.264-265.636 |
0.363 |
|
2011 |
Ozturk F, Arslan MA. Analysis of Temperature Distribution on Warm Forming of Aluminum-Magnesium Alloy Advanced Materials Research. 329-336. DOI: 10.4028/Www.Scientific.Net/Amr.264-265.329 |
0.349 |
|
2011 |
Toros S, Ozturk F. Flow curve prediction of Al-Mg alloys under warm forming conditions at various strain rates by ANN Applied Soft Computing. 11: 1891-1898. DOI: 10.1016/J.Asoc.2010.06.004 |
0.476 |
|
2011 |
Ozturk F, Pekel H, Halkaci HS. The Effect of Strain-Rate Sensitivity on Formability of AA 5754-O at Cold and Warm Temperatures Journal of Materials Engineering and Performance. 20: 77-81. DOI: 10.1007/S11665-010-9652-Y |
0.469 |
|
2010 |
Ozturk F, Toros S, Kilic S. Tensile deformation behavior of AA5083-H111 at cold and warm temperatures International Journal of Materials Research. 101: 1172-1179. DOI: 10.3139/146.110391 |
0.46 |
|
2010 |
Ozturk F, Ece RE, Polat N, Koksal A. Effect of warm temperature on springback compensation of titanium sheet Materials and Manufacturing Processes. 25: 1021-1024. DOI: 10.1080/10426914.2010.492056 |
0.329 |
|
2010 |
Ozturk F, Esener E, Toros S, Picu CR. Effects of aging parameters on formability of 6061-O alloy Materials and Design. 31: 4847-4852. DOI: 10.1016/J.Matdes.2010.05.050 |
0.352 |
|
2010 |
Ozturk F, Sisman A, Toros S, Kilic S, Picu RC. Influence of aging treatment on mechanical properties of 6061 aluminum alloy Materials & Design. 31: 972-975. DOI: 10.1016/J.Matdes.2009.08.017 |
0.383 |
|
2010 |
Toros S, Ozturk F. Modeling uniaxial, temperature and strain rate dependent behavior of Al―Mg alloys Computational Materials Science. 49: 333-339. DOI: 10.1016/J.Commatsci.2010.05.019 |
0.442 |
|
2010 |
Picu RC, Ozturk F, Esener E, Li R. Aluminum Alloys with Identical Plastic Flow and Different Strain Rate Sensitivity Metallurgical and Materials Transactions a-Physical Metallurgy and Materials Science. 41: 3358-3364. DOI: 10.1007/S11661-010-0423-Z |
0.427 |
|
2009 |
Ozturk F, Toros S, Pekel H. Evaluation of tensile behaviour of 5754 aluminium–magnesium alloy at cold and warm temperatures Materials Science and Technology. 25: 919-924. DOI: 10.1179/174328408X365775 |
0.435 |
|
2009 |
Ozturk F, Toros S, Kilic S. Tensile and Spring-Back Behavior of DP600 Advanced High Strength Steel at Warm Temperatures Journal of Iron and Steel Research International. 16: 41-46. DOI: 10.1016/S1006-706X(10)60025-8 |
0.379 |
|
2008 |
Evis Z, Ozturk F. Investigation of tensile strength of hydroxyapatite with various porosities by diametral strength test Materials Science and Technology. 24: 474-478. DOI: 10.1179/174328408X278439 |
0.345 |
|
2008 |
Toros S, Ozturk F, Kacar I. Review of warm forming of aluminum-magnesium alloys Journal of Materials Processing Technology. 207: 1-12. DOI: 10.1016/J.Jmatprotec.2008.03.057 |
0.379 |
|
2007 |
Bayrak M, Ozturk F, Demirezen M, Evis Z. Analysis of tempering treatment on material properties of DIN 41Cr4 and DIN 42CrMo4 steels Journal of Materials Engineering and Performance. 16: 597-600. DOI: 10.1007/S11665-007-9043-1 |
0.334 |
|
2007 |
Ozturk F, Lee D. A New Methodology for Ductile Fracture Criteria to Predict the Forming Limits Journal of Materials Engineering and Performance. 16: 224-228. DOI: 10.1007/S11665-007-9036-0 |
0.655 |
|
2005 |
Picu RC, Vincze G, Ozturk F, Gracio JJ, Barlat F, Maniatty AM. Strain rate sensitivity of the commercial aluminum alloy AA5182-O Materials Science and Engineering A. 390: 334-343. DOI: 10.1016/J.Msea.2004.08.029 |
0.466 |
|
2005 |
Ozturk F, Lee D. Experimental and numerical analysis of out-of-plane formability test Journal of Materials Processing Technology. 170: 247-253. DOI: 10.1016/J.Jmatprotec.2005.05.010 |
0.664 |
|
2004 |
Ozturk F, Lee D. Analysis Of Forming Limits Using Ductile Fracture Criteria Journal of Materials Processing Technology. 147: 397-404. DOI: 10.1016/J.Jmatprotec.2004.01.014 |
0.674 |
|
Show low-probability matches. |